|
|
|
1967 -1968 Camaro Exhaust System
1967-1968 Camaro Big and Small Block Deep Tone Exhaust Kit. This kit includes 2 1/4" head pipes with correct flats and wrinkle bends, 2 1/4" over axle pipes and tail pipes with correct oval shaped angle cut. Correct muffler reproduced from an original will be included as well as extensions donuts and flanges. This kit includes all the correct rounded bottom and guillotine clamps. Correct two hole front hangers and right and left tail pipe hangers. Small and big block heat risers are an option as well as stud kit with correct lock nuts. Correct strap clamps with sheet metals screws are available with our concours show package. Kit will include installation instructions and diagrams for easy assembly. This particular kit shown here is for 1968 Camaro 396 with a concours show pkg. |
|
|
1967-1968 Camaro Big Block Deep Tone Exhaust System Kit |
|
|
|
|
|
|
1968 Yenko Non Converted Copo Owned by Tom Billigen Equiped With Gardner Exhaust |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
I'm based in the UK and have been restoring my early build 1968 Z28 Camaro for the past two years. Because the car is totally original and is being restored that way down to the very last detail one of my challenges is ensuring that the parts that I use are 100% correct and fit first time. Being based in the UK adds to the normal list of potential problems we all face when restoring a car 40 years plus of age. I don't have the luxury of easily returning parts, especially large ones that don't measure up to my standards which are high, or I should I say I just expect things to be correct and as described as too often they are not.
I recently purchased from you a Small Block Deep Tone Exhaust Kit with Concours Package which I must say is worth the additional investment. I just thought that I would take the time out to write to you and thank you for being true to your word and delivering on your promises. The exhaust and all of it's components look absolutely stunning and were a dream to fit. The whole system was all connected up in a couple of hours with no frustrations or alterations required whatsoever which is what I would expect from a quality restoration part so thank you. It almost seems a shame to hide the exhaust away under the car it's that good but I'm sure it will get noticed at the shows when the true enthusiast's start crawling around underneath it as they do.
If anyone is in any doubt about what system to choose for their classic car and has exacting standards like me and your other customers then look no further than Gardner Exhaust Systems.
|
|
|
1968 Camaro Z/28 Undercarriage restored by Mike Dietrich Equipped With Gardner Exhaust |
|
|
|
1967 -1968 Camaro Clamp
This is the exact correct clamp for the 1967-69 Camaros. This clamp was used at the muffler inlet. The clamp seen here has not been available for a very long time. It is another Gardner Exlclusive reproduction and is availble with one of our show quality exhaust systems.
|
|
|
1967 -1969 Camaro Clamp
This is the exact correct clamp for the 1967-1969 Camaros. They were used in multiple locations and have been unavailable for many years. They are a Gardner Exhaust esclusive reproduction and are avalable in 2" and 2 1'4" versions. These clamps are available with one of our show quality exhaust systems. |
|
|
|
"
1967-1969 Camaro Front Hanger:
This hanger is another Gardner
Exhaust Exclusive Reproduction. Original hangers used backing plates, smaller rivets corded rubbers and two screw holes instead of five quite often seen in the aftermarket. Our exclusive hangers are built by hand to replicate the originals |
|
|
|
1967-1968 Camaro Tail Hangers:
The hangers pictured here are another Gardner
Exhaust Exclusive Reproduction. Original hangers used backing plates, smaller rivets and corded rubbers and were mirror images of one another. Our exclusive hangers are built by hand to replicate the originals |
|
|
|
|
1967-1969 Camaro Dual Exhaust Right Over Axle Pipe:
This is the 2 1/4" pipe that connects to the end of the head pipe and goes into the transverse muffler on all dual exhaust camaros from 1967-1969 It can be seen next to the original it was copied from. |
|
|
|
1967-1968 Camaro Dual Exhaust Tail PIpes Our correct 2 1/4" tail pipes have been reproduced from the original in the picture and come with corrrect oval shaped angle cut finish.
|
|
|
|
1967 -1968 Camaro Strap Clamp
This is the correct strap clamp that was originally used to attach the tail pipes to the tail pipe hangers. They come zinc plated to aid in longevity and have been reproduced from the original next to it. |
|
|
|
1967-1969 Camaro Big Block Resonator left head pipe
This pipe has been placed next to an original to show the reproduction authenticity.
All correct flats, wrinkles bends and reductions that were in the original are in our reproduction. |
|
|